Brother DCP-9045CDN Service Manual Download Page 33

Page: 33 / 491

Confidential

1-14

Error code 38

Print Unable 38

Turn the power off and then back on again.

THM (Thermistor) sensor failure

Error code 39

Print Unable 39

Turn the power off and then back on again.

HUM (Humidity) sensor failure

Step

Cause

Remedy

Harness connection failure of

THM/HUM sensor

Check the harness connection of the THM/HUM

sensor and reconnect it.

THM/HUM sensor failure

Replace the THM/HUM sensor holder ASSY.

Engine PCB failure

Replace the engine PCB ASSY.

Error code 3A

Print Unable 3A

Turn the power off and then back on again.

Error code 7C

Print Unable 7C

Turn the power off and then back on again.

Engine communication error

Step

Cause

Remedy

Harness connection failure
between engine PCB and
main PCB

Check the harness connection between the engine
PCB and main PCB, and reconnect it.

Engine PCB failure

Replace the engine PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Related manuals for DCP-9045CDN

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Related manuals for DCP-9045CDN

Brands by name

Popular brands