manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 244

Confidential 

3-111

(11) Remove the double-faced adhesive tape which is attached between the FFC cable ASSY 

and CCD unit, and disconnect the FFC cable ASSY from the CCD unit. 

Note: 

- After disconnecting the flat cable(s), check that each cable is not damaged at its end or 

short-circuited. 

- When connecting the flat cable(s), do not insert it at an angle. After insertion, check that 

the cable is not at an angle. 

 

Fig. 3-138 

(12) Push the Pulley ASSY to the direction of the arrow 12a and remove the CCD drive belt. 

 

Fig. 3-139 

CCD unit 

Double-faced adhesive tape 

FFC cable ASSY 

Connector 

CCD drive belt

Pulley ASSY 

12a 

12b 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands