manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 182

Confidential 

3-49

8.9  Paper Guide/ HV TR Top Cover 

(1)  Release the two Bosses, and then remove the Paper guide from the Transfer HVPS PCB 

unit while lifting it up slightly. 

Note: 

When removing the Paper guide, be careful not to damage the two Ribs. 

 

Fig. 3-28 

(2)  Slide the HV TR top cover to the left hand side and release the four Hooks. Then, remove 

the HV TR top cover. 

 

Fig. 3-29 

Boss 

Hook 

Transfer HVPS PCB unit 

Boss 

Hook 

Paper guide 

HV TR top cover 

Hooks 

Transfer HVPS PCB unit 

Hooks 

<Back side> 

<Back side> 

Ribs 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands