Bosch VIP XD Installation And Operating Manual Download

Page: 7 / 80

XIP XD

Safety Information | en

Bosch Security Systems

Installation and Operating Manual

DOC | V4.0 | 2009.06

Safety Information

2.1

Electric Shock Hazard

–

Never attempt to connect the unit to any power network other than the type for which it

is intended.

–

Use only the power supply unit provided.

–

Never open the housing.

–

Never open the housing of the power supply unit.

–

If a fault occurs, disconnect the power supply unit from the power supply and from all

other units.

–

Install the power supply and the unit only in a dry, weather-protected location.

–

If safe operation of the unit cannot be ensured, remove it from service and secure it to

prevent unauthorized operation. In such cases, have the unit checked by Bosch Security

Systems.

Safe operation is no longer possible in the following cases:

–

if there is visible damage to the unit or power cables,

–

if the unit no longer operates correctly,

–

if the unit has been exposed to rain or moisture,

–

if foreign bodies have penetrated the unit,

–

after long storage under adverse conditions, or

–

after exposure to extreme stress in transit.

2.2

Installation and Operation

–

The relevant electrical engineering regulations and guidelines must be complied with at

all times during installation.

–

Relevant knowledge of network technology is required to install the unit.

–

Before installing or operating the unit, make sure you have read and understood the

documentation for the other equipment connected to it, such as monitors. The

documentation contains important safety instructions and information about permitted

uses.

–

Perform only the installation and operation steps described in this manual. Any other

actions may lead to personal injury, damage to property or damage to the equipment.

2.3

Maintenance and Repair

–

Never open the housing of the VIP XD. The unit does not contain any user-serviceable

parts.

–

Never open the housing of the power supply unit. The power supply unit does not contain

any user-serviceable parts.

–

Ensure that all maintenance or repair work is carried out only by qualified personnel

(electrical engineers or network technology specialists).

Summary of Contents for VIP XD

















































































Search results

Summary of Contents for VIP XD

Reviews:

Related manuals for VIP XD

Brands by name

Popular brands

Bosch VIP XD, Installation And Operating Manual

Search results

Summary of Contents for VIP XD

Reviews:

Related manuals for VIP XD

Brands by name

Popular brands