Bosch VIP XD Installation And Operating Manual Download

Page: 61 / 80

VIP XD

Maintenance and Upgrades | en

Bosch Security Systems

Installation and Operating Manual

DOC | V4.0 | 2009.06

Maintenance and Upgrades

7.1

Testing the Network Connection

You can use the

ping

command to check the connection between two IP addresses. This

allows you to test whether a unit in the network is active.

Open the DOS command prompt.

Type

ping

followed by the IP address of the unit.

If the unit is found, the response appears as

Reply from ...

followed by the number of bytes

sent and the transmission time in milliseconds. If not, the unit cannot be accessed over the

network. This might be because:

–

The unit is not correctly connected to the network. Check the cable connections in this

case.

–

The unit is not correctly integrated into the network. Check the IP address, subnet mask

and gateway address.

7.2

Unit Reset

You can use the Factory Reset button to restore the unit to its original settings. Any changes

to the settings are overwritten by the factory defaults. A reset may be necessary, for example,

if the unit has invalid settings that prevent it from functioning as desired.

If necessary, back up the current configuration using the

Download

button on the

Maintenance

configuration page (see

Section 5.21 Maintenance, page 49

Using a pointed object, press the factory reset button until the operating status LED

flashes red (see

Section 3.5 Connections on the Rear Panel, page 14

). All settings will

revert to their defaults.

Change the IP address of the VIP XD if necessary.

Configure the unit to meet your requirements.

CAUTION!

All configured settings will be discarded during a reset.

If necessary, back up the current configuration using the

Download

button on the

Maintenance

configuration page (see

Section 5.21 Maintenance, page 49

NOTICE!

After a reset, the unit can only be addressed via the factory default IP address. The IP address

can be changed as described in the

Installation

chapter (see

Section 4.4 Setup Using the

Configuration Manager, page 19

Summary of Contents for VIP XD

















































































Search results

Summary of Contents for VIP XD

Reviews:

Related manuals for VIP XD

Brands by name

Popular brands

Bosch VIP XD, Installation And Operating Manual

Search results

Summary of Contents for VIP XD

Reviews:

Related manuals for VIP XD

Brands by name

Popular brands