Bosch SHI 4302 Manual Download Page 93

Page: 93 / 144

VIII.

Troubleshooting

Dispenser

–

Top Load Dispenser (1)

Many high-end models (with digital displays) have top-
load dispensers, enabling detergent and rinse-aid to be
added while doors are partially open (preferably @ 45º).

Rinse-aid dosage is shown
on the digital display and is
changed through the
dishwasher controls, not
through a dispenser dial.

HINT:

Top-load dispensers are mounted

similarly to standard dispensers.

Push onto the

blue

button to release the
detergent cup (once the
door has been opened).

NOTE:

Top-load and standard

dispensers are

NOT

interchangeable.

Standard dispenser

Top-load dispenser

HINT:

Check the Use & Care Manual on

changing top-load dispenser rinse-aid
dosage using dishwasher controls.

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands