Bosch SHI 4302 Manual Download Page 90

Page: 90 / 144

VIII.

Troubleshooting

Heater

–

Water Switch (“Flow Control”) (2)

Part description

Old part #

Models used on

Water switch

part #

Models used on

Circulation pump

491434

(pum p)

266511

(m otor only)

All models (index #’s

UC/07, UC/11 & UC/12)

239129

(pump)

All

ExactWash

Apexx

models (index # UC/14)

Pump motor starter

--------

--------

182318

All

ExactWash

Apexx

models (index # UC/14)

Heater assembly

Various

Various

219639 or

431412

All

ExactWash

Apexx

models (index # UC/14)

Sump

263103

All models (index #’s

UC/07, UC/11 & UC/12)

482035

All

ExactWash

Apexx

models (index # UC/14)

Pump support straps

171596

All models (index #’s

UC/07, UC/11 & UC/12)

171596

All models (index #’s UC/07,

UC/11, UC/12 & UC/14)

Pipe clamp (pump to heater)

172272

All models (index #’s

UC/07, UC/11 & UC/12)

172272

All models (index #’s UC/07,

UC/11, UC/12 & UC/14)

Pump rear housing

267739

All models (index #’s

UC/07, UC/11 & UC/12)

267739

All models (index #’s UC/07,

UC/11, UC/12 & UC/14)

Pump front housing

266514

All models (index #’s

UC/07, UC/11 & UC/12)

266514

All models (index #’s UC/07,

UC/11, UC/12 & UC/14)

NOTE:

This does

not

affect (Sensotronic)

models without water switches. They use
the same parts used on models from
UC/06 through UC/12.

NOTE:

This affects (ExactWash & Apexx)

models with

water switches --

SH_56

SHV/Y66

SH_99

NOTE:

Parts can be changed without notice.

Please refer to published CD parts lists for up
to date part #’s.

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands