Bosch SHI 4302 Manual Download Page 80

Page: 80 / 144

VIII.

Troubleshooting

Circulation Pump

–

Service Index UC/06, UC/11 & UC/12 Parts

Changes

Part description

Old part #

Models used on

Softer bearing

part #

Models used on

Circulation pump

263835

(m otor only)

All models (index #’s

UC/06 & UC/09)

491434

(pum p)

266511

(m otor only)

All models (index #’s

UC/07, UC/11 & UC/12)

Pump support bushings

167244

All models (index #’s

UC/06 & UC/09)

--------

--------

Pump support straps

--------

--------

171596

All models (index #’s

UC/07, UC/11 & UC/12)

Gasket (pump to heater)

165268

All models (index #’s

UC/06 & UC/09)

--------

--------

Pipe clamp (pump to heater)

--------

--------

172272

All models (index #’s

UC/07, UC/11 & UC/12)

Pump rear housing

263314

All models (index #’s

UC/06 & UC/09)

267739

All models (index #’s

UC/07, UC/11 & UC/12)

Pump front housing

263838

All models (index #’s

UC/06 & UC/09)

266514

All models (index #’s

UC/07, UC/11 & UC/12)

Seal (pump to sump)

165269

All models (index #’s

UC/06 & UC/09)

171598

All models (index #’s

UC/07, UC/11 & UC/12)

NOTE:

Most circulation pump part #’s have changed due to the “

softer bearing

” upgrade -

- the circulation pump has been suspended by flexible straps instead of being mounted onto
the base (onto rubber bushings) to make the dishwashers quieter. The impeller kit hasn’t
changed – its still #

167085

NOTE:

Parts can be changed without notice. Please refer to published CD

parts lists for up to date part #’s.

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands