Bosch SHI 4302 Manual Download Page 41

Page: 41 / 144

SHY56A/66C

SHU 995x

SHV 68

control modules are

different than other models and are removed differently.

VI.

Component Access/Replacement

Control Modules

Disassembly (2)

Remove fascia panel by removing six (6)T-20
Torx inner door screws.

Disconnect wire harnesses from module
after noting connector locations.

Remove fascia panel from console by
removing four (4) T-20 Torx screws.

Remove two (2) T-20 Torx screws holding
module to console.

Carefully pry back locking tabs on each front
corner of module, then remove module from
console. Remove button pad from module.

(SHU 995x shown)

These instructions apply to

SHY56A/66C, SHU 995x &

SHV 68 models.

Removing door screws

Removing fascia screws

Removing module screws

Prying back module tabs

Sliding module out

Align tabs when reassembling

Removing button pad --

buttons can come off pad

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands