Bosch SHI 4302 Manual Download Page 59

Page: 59 / 144

VI.

Component Access/Replacement

Aqua Sensors

The aqua sensor is located on the rear of the sump. It
can be reached through the left side of the dishwasher
(after the left side panel is removed). Its not necessary
to block up the tank to reach the aqua sensor.

Sump

Base

Tank

HINT:

To change out the aqua

sensor, pull off the connector
and pull out the aqua sensor
(toward the rear of the
dishwasher).

HINT:

The aqua sensor slides

into slots in the sump. Make
sure the aqua sensor is properly
inserted into the slots.

NOTE:

The

Apexx Sensotronic 2

aqua sensor #

175340

similar to standard aqua sensor #

165279

, except it has two

(red & green) soil sensors. They mount the same way, but
are

not

interchangeable.

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands