Bosch SHI 4302 Manual Download Page 82

Page: 82 / 144

VIII.

Troubleshooting

Circulation Pump

–

Pump & Motor Part # Changes

HINT:

The preferred repair for

replacing pump impellers is the #

167085

impeller kit. The other

solution is using complete pump

assembly #

239144

. The #

266511

pump motor only should only be used if

the motor fails (which rarely happens).

NOTE:

The #

167085

impeller kit

and #

263835

index UC/06

circulation pump motor only part #’s

have not changed and still are used.

NOTE:

The circulation pump

assembly part # has been changed

from #

266511

to #

239144

Please check all pumps ordered or

already in stock to make sure they

show part #

239144

167085

impeller kit

167235

capacitor

266511

motor only

239144

complete pump

assembly

266514

front pump housing

267739

rear pump

housing

171598

sump-pump gasket

The softer bearing (UC/07, UC/11 & UC/12 index) circulation pump and motor
only part #’s for all

models have been changed to make

parts ordering more consistent throughout the world. All

parts in stock have been changed to these new part #’s as follows:

•

239144

-- complete circulation

pump assembly (with impeller) for
all

dishwasher models with softer
bearing (all models with index #’s
UC/07, UC/11 & UC/12)

•

266511

-- circulation pump motor

only for all

dishwasher models with softer
bearing (all models with index #’s
UC/07, UC/11 & UC/12)

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Bosch SHI 4302, Manual, Page: 82 / 144

Search results

Summary of Contents for SHI 4302

Reviews: