Bosch SHI 4302 Manual Download Page 86

Page: 86 / 144

VIII.

Troubleshooting

Control Module

–

Using # 481055 Control Modules in Older

SHU 99 and SHV 43/48 Dishwashers (2)

button pushbutton pad # 182600 used on SHV 48

UC/06, UC/07, UC/11 & UC/12 and SHU 992x UC/12

button pushbutton pad # 182605 used on SHV 43,

SHU 991x UC/06, UC/11 & UC/12 and SHU 990x UC/06

New pushbutton pads:

INSTRUCTIONS FOR TURNING OFF END OF CYCLE TONE:

Open door, push and hold

Delicate/Econo

button, then turn

dishwasher on while holding

Delicate/Econo

button.

Release

Delicate/Econo

button. If module beeps, then end of

cycle tone is on. Press

Delicate/Econo

button to disable tone.

If module doesn’t beep after button is pressed, then tone is
disabled.

Turn off dishwasher to save selection.

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands