Bosch SHI 4302 Manual Download Page 52

Page: 52 / 144

VI.

Component Access/Replacement

Heaters &

NTC’s

–

Removal & Installation (1)

Removing & Installing Heater & NTC:

Remove two (2) T-20 Torx screws
holding heater assembly to sump.

Disconnect wires from heater, flow
switch, NTC & Hi-Limit after noting
connections.

Pull clips, then carefully pull heater
assembly from sump & pump. Note
heater comes as an assembly (with
housing & gasket).

NOTE:

Softer bearing &

non-softer bearing
heater assemblies,
circulation pumps and
sumps

cannot

be mixed

and matched. Softer
bearing heaters don’t fit
in older models and
older heaters don’t fit in
softer bearing models.

HINT:

If needed, use rinse-aid to lubricate gaskets to make

it easier to assemble heater to sump and pump.

Pull clips

Heater assembly

Remove heater screws

Remove heater

NOTE:

Softer bearing & non-softer bearing heater

assemblies are connected to circulation pumps differently:

• Softer bearing models (UC/11 & above) have gasket

assembled to heater and have a separate hose clamp
(order #

172272

• Older models (UC/06) have a separate gasket and do

not have a hose clamp.

“Softer

bearing” heater

Hose clamp

HINT:

Heater assemblies contain NTC’s, Hi-Limit’s & flow switches (& aqua

sensors where applicable). If heaters are replaced, these parts are replaced too.

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands

Bosch SHI 4302, Manual

Search results

Summary of Contents for SHI 4302

Reviews:

Related manuals for SHI 4302

Brands by name

Popular brands