Bosch SHI 4302 Manual Download Page 71

Page: 71 / 144

VIII. Troubleshooting

Heater

Troubleshooting Flowchart

With heater on

(during test

program), measure

dishwasher

incoming current

(black wire).

If ~ 11A,

heater is

working

fine.

If ~ 1.5A,

heater

circuit has

failed.

Measure

voltage @

control

module.

If ~120 VAC,

check heater

circuit.

If ~ 0 VAC, control module

(heater relay) has failed.

Replace faulty module.

Measure

resistance

@ heater

terminals.

If ~11 , check

high limit &

flow switch.

If , heater

has failed

(opened).

Replace

heater.

If ~ 0, heater

has failed
(shorted).

Replace

heater.

Measure high

limit & flow

switch

resistance.

If high limit ~ 0.3 & flow

switch ~ 0.4 , check wire

harnesses. Replace faulty

harness.

If high limit or

flow switch = ,

replace faulty

part.

START

Troubleshooting Flowchart

NOTE:

Flow through heaters

heat water ~ 2ºF / minute.

Can also measure heater

current @ module red

heater wire (~ 9.5A).

Summary of Contents for SHI 4302

















































































































































Search results

Summary of Contents for SHI 4302

Reviews:

Bosch SHI 4302, Manual, Page: 71 / 144

Search results

Summary of Contents for SHI 4302

Reviews: