Bosch B8512G Program Entry Manual Download Page 73 | Manualshive

Page: 73 / 284

background image

Control Panel

Panel Wide Parameters | en

73

Bosch Security Systems, Inc.

Program Entry Guide

2017.03 | 09 | F.01U.303.998

3.14.6

Answer Armed

Default

: 7

Selections

: 0 to 15 (rings)

–

0 (zero) This setting disables answering the phone.

–

1 to 15 Use this setting to have the control panel answer the phone after the specified
number of rings when all areas are All On

Notice!

RPS considers Part On as a disarmed state.

This parameter sets the telephone ring counter to answer when all areas are All On. If any area
in the control panel is Part On or disarmed, the Answer Disarmed, page 73 ring counter is
used.

Notice!
PSTN requirement for Australia / New Zealand, disable RPS answer armed/disarmed

If you set the Panel Wide Parameters > Phone Parameters > PSTN Compatibility parameter to
Australia or New Zealand, you must set this Answer Armed and the Answer Disarmed
parameter to 0 (disabled).

RPS Menu Location

Panel Wide Parameters > RPS Parameters > Answer Armed

3.14.7

Answer Disarmed

Default

: 7

Selections

: 0 to 15 (rings)

–

0 (zero) - this setting disables answering the phone.

–

1 to 15 - use this setting to have the control panel answer the phone after the specified
number of rings when all areas are All On.

Notice!

RPS considers Part On as a disarmed state.

This parameter sets the telephone ring counter to answer when any area is in a Part On or
disarmed state.

Notice!
PSTN requirement for Australia / New Zealand, disable RPS answer armed/disarmed

If you set the Panel Wide Parameters > Phone Parameters > PSTN Compatibility parameter to
Australia or New Zealand, you must set the Answer Armed and this Answer Disarmed
parameter to 0 (disabled).

RPS Menu Location

Panel Wide Parameters > RPS Parameters > Answer Disarmed.

3.14.8

RPS Phone #

Default

: Blank

Selections

: Up to 24 characters

This parameter specifies the phone number the control panel dials to contact RPS.

«
...
71
72
73
74
75
...
»

Summary of Contents for B8512G





























































































































































































































































































Reviews:

No comments

Related manuals for B8512G

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: Hanwell Pages: 34

Brand: HANSONG Pages: 11

Brand: Datapath Pages: 12

Brand: Hansen Pages: 4

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: Ziton Pages: 36

Brand: GEA Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands