Bosch B8512G Program Entry Manual Download Page 246 | Manualshive

Page: 246 / 284

background image

246

en | SDI2 modules

Control Panel

2017.03 | 09 | F.01U.303.998

Program Entry Guide

Bosch Security Systems, Inc.

RPS Menu Location

SDI2 > IP Communicator > Web and Automation Security

14.4.22

Alternate IPv4 DNS server IP address

Default

: 0.0.0.0

Selections

: 0.0.0.0 to 255.255.255.255

This parameter provides an alternate IPv4 DNS server IP address.
If the IP communicator fails to obtain an address from the primary server, it tries the alternate
DNS server.

Further information

IP Address and Domain Name formats, page 282

RPS Menu Location

SDI2 > B42x IP Communicator > Alternate IPv4 DNS server IP address

14.4.23

Alternate IPv6 DNS server IP address

Default

: ::

Selections

: 0000:0000:0000:0000:0000:0000:0000:0000 to

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
This parameter provides an alternate IPv6 DNS server IP address.
The Alternate IPv6 Domain Name Server (DNS) address has a hexadecimal notation, which
consists of the eight groups of the address expressed separately in hexadecimal and
separated by colons. Each group has a value between 0000-FFFF.
When this is defined through the DHCP service, leave the default value. If the module fails to
obtain an address from the primary server, the Alternate IPV6 DNS server is used, if specified.
The module can use the Alternate IPv6 DNS server only when the Primary address is not the
default address.

Further information

IP Address and Domain Name formats, page 282

RPS Menu Location

SDI2 > B42x IP Communicator > Alternate IPv6 DNS server IP address

14.5

B450 cellular

14.5.1

Inbound SMS

Notice!
Important configuration information for cellular communication

Refer to Configuring for Cellular Service, page 280 for an overview and configuration
information.

Default

: Yes

Selections

:

Yes - Enabled
No - Disabled
This parameter enables an RPS user to start a control panel initiated download with an SMS
message.

RPS menu location

SDI2 modules > IP Communicator > B450 Cellular > Inbound SMS

«
...
244
245
246
247
248
...
»

Summary of Contents for B8512G





























































































































































































































































































Reviews:

No comments

Related manuals for B8512G

ControlMaster CM15

Brand: ABB Pages: 28

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

Brand: Samsung Pages: 32

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

Brand: olympia electronics Pages: 10

Brand: Paradox Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

Brand: YASKAWA Pages: 121

Brand: YASKAWA Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands