Bosch B8512G Program Entry Manual Download Page 38 | Manualshive

Page: 38 / 284

background image

38

en | Panel Wide Parameters

Control Panel

2017.03 | 09 | F.01U.303.998

Program Entry Guide

Bosch Security Systems, Inc.

3.3.5

Reporting Delay for No Towers (sec.)

Notice!
Important configuration information for cellular communication

Refer to Configuring for Cellular Service, page 280 for an overview and configuration
information.

Default

: 0

Selections

: 0-3600 (seconds)

–

0 - Disabled.

–

1 to 3600 - Enabled.

When there are no towers present the control panel starts two timers, one for a
No Towers event, one for a No IP Address event. The control panel uses the duration set by
this Reporting Delay for No Tower parameter for both timers. If the cellular plug-in module
does not find a tower before the end of the delay, the control panel creates a No Towers event
and a No IP Address event at the same time.
The control panel creates a No Tower restoral event when one or more towers are available for
the duration set by this Reporting Delay for No Tower parameter.
The contro panel creates a No IP Address restoral event when the cellular plug-in module
successfully registers with one or more towers and receives an IP address.

Notice!
When one or more towers are available, 60 second delay for No IP Address event

If the cellular plug-in module successfully registers with one or more towers, but does not
receive an IP address within 60 seconds, the control panel creates a No IP Address event.

RPS Menu Location

Panel Wide Parameters > Cellular Plug-in Module > Reporting Delay for No Towers

3.3.6

Outgoing SMS Length

Notice!
Important configuration information for cellular communication

Refer to Configuring for Cellular Service, page 280 for an overview and configuration
information.

Default

: 160

Selections

: 0 to 3600 (bytes)

–

0 - Disabled.

–

1 to 3600 - Outgoing SMS length (number of bytes)

This parameter sets the maximum length for outgoing messages.
Outgoing SMS messages are rejected if over this length. This maximum length must match the
maximum length set by the cellular provider that is transmitting the SMS message (for
example, Verizon).

RPS Menu Location

Panel Wide Parameters > Cellular Plug-in Module > Outgoing SMS Length

«
...
36
37
38
39
40
...
»

Summary of Contents for B8512G





























































































































































































































































































Reviews:

No comments

Related manuals for B8512G

Brand: Lawler Pages: 2

SolarCell Remote

Brand: Samsung Pages: 2

Brand: V2 ELETTRONICA Pages: 72

Brand: Parkside Pages: 86

Brand: Universal Remote Pages: 20

Brand: Zaiput Flow Technologies Pages: 10

Brand: WAC Pages: 5

Brand: A.R.I. Pages: 14

Brand: Industrial Controls Pages: 17

Brand: SolarEdge Pages: 20

SmarTemp Control fx

Brand: Webasto Pages: 8

Brand: National Instruments Pages: 4

Brand: UUGear Pages: 38

Brand: Nibe Pages: 20

GA INSTRUMENTS K-1255

Brand: Vag Pages: 7

Brand: B meters Pages: 2

easy2read Lepton3x1

Brand: Caen RFID Pages: 31

Brand: Laserworld Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands