Bosch B8512G Program Entry Manual Download Page 88 | Manualshive

Page: 88 / 284

background image

88

en | Panel Wide Parameters

Control Panel

2017.03 | 09 | F.01U.303.998

Program Entry Guide

Bosch Security Systems, Inc.

Callout - Description

1 - Alarm event

2 - Compatible Bosch control panel

3 - Internet

4 - SMTP email server

5 - Computer or other device used to receive email

SMTP Email Servers

SMTP email servers transfer messages to personal notification email addressees. Refer to
Email Server Name/Address for a list of some of the more popular servers and their addresses.
If you can't locate the address for your SMTP email server, contact your email provider.

Setting up an Email Account

To setup an email account that sends emails to the Personal Notification Destinations:
1.

Register for an email account from an email provider (example: Google, Yahoo, AOL,
Microsoft).

2.

Choose a user name that makes it easy for the individuals receiving the notifications to
identify which emails are coming from the control panel (example: panelacctstore52).

3.

Enter the address associated with the SMTP email server you chose in the Email Server
Name/Address parameter.

4.

Enter the user name you specified when registering for this account in the Authentication
User Name parameter.

5.

Enter the password you specified when registering for this account in the Authentication
Password parameter.

3.19.1

Email server name/address

Default

: Blank

Selections

: Domain name or IP address

This parameter specifies either the domain name or address for the SMTP (Simple Mail
Transfer Protocol) email server for your chosen email provider. The control panel uses the
server's domain name (or address) to transfer event messages from the control panel to
designated personal notification email addressees.

SMTP Email Servers

Refer to the table below for the some of the more popular email providers and their server's
domain name. If your provider doesn't appear in the table, contact them for their domain
name (or IP address).

Email provider

Domain name

1&1

smtp.1and1.com

«
...
86
87
88
89
90
...
»

Summary of Contents for B8512G





























































































































































































































































































Reviews:

No comments

Related manuals for B8512G

Brand: Waterway Pages: 16

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brand: Eaton Pages: 6

Brand: Eaton Pages: 35

Brand: Eaton Pages: 18

Brand: Eaton Pages: 73

Brand: Eaton Pages: 4

Cutler-Hammer IQ DP-4000

Brand: Eaton Pages: 87

Brand: Eaton Pages: 14

Brand: Eaton Pages: 36

Brand: fakro Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands