Bosch B8512G Program Entry Manual Download Page 121 | Manualshive

Page: 121 / 284

background image

Control Panel

Keypads | en

121

Bosch Security Systems, Inc.

Program Entry Guide

2017.03 | 09 | F.01U.303.998

Notice!

SDI2 keypads are always supervised regardless of this parameter's setting.

Notice!

Keypads sharing the same address setting display the same text and sound the same tones
regardless of which keypad keys are being pressed.

Notice!

TROUBLE SDI # reports are always reported as Area 1, Account 1 events regardless to which
area the SDI device is assigned.

Notice!

When this parameter is set to Yes, you cannot have duplicate DIP switch settings.

RPS Menu Location

Keypads > Keypad Assignments > Supervision

5.1.34

D125X Passcode [Esc] Option

Default

: Yes

Selections

:

–

Yes - entering a user passcode followed by the [Esc] key performs the legacy D125x
sequence. If bells are sounding alarms, the alarms are acknowledged. If no bells are
sounding and either silence or clear operations are allowed, the clear display task is
executed.

–

No - pressing the [Esc] key erases the last digit and if no digits are entered the task is
exited.

Notice!

This option is only available on D-Series D125x keypads from the Idle task only.

Notice!

Only available when "D125xRB Fire Keypad (SDI)" or the "D1255 VFD keypad (SDI)" is
selected as the Keypad Type, page 110.

RPS Menu Location

Keypads > Keypad Assignments > D125X Passcode [ESC] Option

5.2

Global Keypad Settings

5.2.1

A key Response

Default

: No Response

Selections

:

–

No Response (Invalid key press response)

–

Manual Fire Alarm (When A key and 1 key are held together for 2 sec.)

«
...
119
120
121
122
123
...
»

Summary of Contents for B8512G





























































































































































































































































































Reviews:

No comments

Related manuals for B8512G

Brand: E-fly Pages: 16

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

Brand: Rane Pages: 2

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Jäger Pages: 18

Brand: Anilam Pages: 31

Brand: Rinnai Pages: 7

Brand: Aqua Lung Pages: 24

Brand: Zonex Pages: 16

DX99N9X1S2N0M2X0D2

Brand: Banner Pages: 13

AWH18QD-D3DNA3G/I

Brand: AC Pro Pages: 48

Brand: CompuSTAR Pages: 8

Brand: RC-Timing Pages: 21

Brand: Kathrein Pages: 32

Brand: Rain Bird Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands