Belarus 1221.2 Operator'S Manual Download

Page: 212 / 295

BELARUS-

1221.2/1221В.2/1221.3

Aggregation

211

tractor, make sure that the hydraulic circuits of the tractor and aggregate are depressur-

ized!

•

When performing the hydraulic connection between the tractor and the machine, it

is necessary to mark beforehand the components to be connected in order to avoid errors

in the control of the units of the hydraulic system of the aggregated machine! Erroneous

connection of the reverse function (for example, lifting or lowering) can cause an accident!

•

When connecting the hydraulic hoses of the machine to the tractor’s hydraulic system,

make sure that the system is depressurized; observe the correctness of the connections be-

tween the hydraulic system of the tractor and the hydraulic system of the aggregate in accor-

dance with marking the hoses and connecting diagram. The connecting diagram shall be

given in the Operation Manual for the machine.

•

Check regularly the condition of the hydraulic hoses. Should any damages or age-

ing signs be revealed, the hoses shall be replaced without delay! The new hoses intended

for substituting the old ones shall comply completely with the manufacturer’s requirements!

•

To avoid injury when determining the leakage places, use appropriate aids! A liquid

(hydraulic oil) flowing out under pressure can penetrate under skin and cause heavy inju-

ries! In case of injury, call immediately for medical aid! Hazard of blood poisoning!

•

Prior to beginning the work with the use of the hydraulic system of the tractor, lower

the machine, depressurize the hydraulic system, stop the engine and remove the ignition

key!

•

Any works with the hydraulic and pneumatic connections of the hydraulic accumula-

tors and receivers of the machines shall be performed with the pressure released!

•

Improper installation and operation of the hydraulic accumulators with violation of

the labour protection requirements can become a cause of heavy accidents.

3.12.8 Tyres, braking system

•

Caution! Do not forget that the pneumatic systems of the tractor and aggregated

machines contain high pressure.

•

Each time prior to departure check the intactness and operability of the brakes!

•

The brake system shall be regularly and thoroughly controlled! The braking system

shall be only adjusted and repaired by a qualified specialist or reliable service department!

Use the recommended brake fluid only! Pour the brake fluid in accordance with the operat-

ing documentation!

•

When operating the machines with transport wheels, it is necessary to ensure the

stable position of the machine (wheel chocks!) to prevent the involuntary rollback!

•

Fitting the tyres requires appropriate habits! It shall be performed by means of spe-

cial fitting tools!

•

The repair works on the tyres and wheels shall be only performed by a qualified

specialist with the use of appropriate fitting tools!

•

Monitor regularly the pressure in the tyres! It shall correspond to the specified

norms!

3.12.9 Maintenance and repair of the machine-tractor aggregates

•

The repair, maintenance, cleaning as well as elimination of functional faults shall be

performed on obligatory condition that the hydraulic system, driving mechanisms and en-

gine are stopped and the ignition key is removed!

•

Check regularly the degree of tightening of bolts and nuts! If necessary, retighten

them! Pay attention to the fasteners of the tractor body, wheels, coupling arrangements

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands