Belarus 1221.2 Operator'S Manual Download

Page: 189 / 295

BELARUS-

1221.2/1221В.2/1221.3

Aggregation

188

Characteristics

Rear HL-2 (3)

Front HL-2

cat. 2

cat. 3

Lower rods

solid

separable

Lower rods length: solid, mm

885

Links hinges width: upper, mm

lower, mm

38 or 45

Connecting elements rated diameter:

upper rod pin, mm

lower rods hinges, mm

22*

28*

22 or 25

Distance between the PTO end and a

suspension axle, mm

595

544

Loading capacity:

on a suspension axle, kN

at 610 mm offset, kN

* Pin and transitional bushings in a tractor set of tools and accessories.

Towing drawbar TD-1 (cross-bar)

Implements: semi-mounted ones (seeders, potato planters, potato harvesters, vegetables

harvesters, etc.), semi-trailers (mowing machines, press-pickups, haulm pickers, etc.),

equipment with a trailing clevis on the towbar.

Повернуто

Turned

Поперечина

Crossbar

Под шкворень

For connecting pin

Отв.

Bore

Fig.

-7.

TD-1 (with a lining for a hinge or without it)

A cross-bar on a suspension axle of a

hitch linkage in a configuration HL-2

Distance between the PTO end and a connecting pin

axis, mm

595

Connecting pin diameter, mm

Vertical load on a TD, kN

6,5

Implement turning angle with reference to a tractor, degrees

± 60

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands