Belarus 1221.2 Operator'S Manual Download

Page: 260 / 295

BELARUS-1221.2/1221V.2/1221.3 Scheduled maintenance

259

Operation 26. Adjust free travel of the

clutch pedal (BELARUS-1221.2/1221.3)

Free travel of the clutch pedal must be 40

to 50 mm.

IMPORTANT!

A too long pedal travel will

not let the clutch to be fully disengaged

and will make the gear switching difficult.

A too short pedal travel will result in slip

of the clutch plates, rapid wear of the

plates and overheating of clutch parts.

•

To adjust the clutch pedal free travel:

•

Unsplint and remove the pin (2), having

disconnected the rod (5) from the lever

(1).

•

Loosen the locknut (4).

•

Unscrew the screw (8) so that the

pedal shaft (6) move up to stop against the

cabin floor.

•

Turn the lever (1) counterclockwise

until it stops, that is, when the release

bearing touches the clutch toggle levers.

•

Unscrewing the fork (3), align the

holes in the fork and the lever (1) and then

screw in the fork into the rod (5) by 5 to 5.5

turns (that is, shorten the rod).

•

Assemble the clutch pedal leverage

in the reverse order.

IMPORTANT!

Make sure that the clutch

pedal always safely returns up to stop

against the floor in the area of pedal free

movement. Otherwise, adjust the

servo-unit spring force (7) using the bolt

(8) or change the position of the bracket

(9) turning it around the axis of the

fastening bolt.

Operation 26a. Adjust free travel of the

clutch pedal (BELARUS-1221V.2)

Perform the operations described in the

section “Adjustments”.

Operation 27. Steering wheel play

With the engine running, the steering angular play must not exceed 25°. Otherwise, check

and eliminate plays in the joints of cylinders, steering link and steering column.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands