Belarus 1221.2 Operator'S Manual Download

Page: 262 / 295

BELARUS-1221.2/1221V.2/1221.3 Scheduled maintenance

261

Before adjusting the parking brake, install

the tractor on an even surface, stop the

engine and lock the rear wheels from front

and rear:

•

Shift the lever (1) to the extreme front (off)

position.

•

Loosen the locknut (2) of the adjustment

bolt (3) of the parking brake (on the right

side of the tractor).

•

Screwing in or out the bolt (3), obtain a

complete disengagement of the parking

brake at the fourth tooth of the sector (A)

under a force on the lever (1) of 350 N.

•

Lock the bolt (3) with the nut (2).

If the tractor is equipped with a pneumatic

system and works with trailers equipped with

pneumatic brakes, adjust the parking brake

as follows:

•

Shift the lever (1) to the extreme front (off)

position.

•

Loosen the locknuts (2) and (6) and

remove the pin (8).

•

Turn the lever (4) so that the upper

edge of the groove in the lever (9) align with

the upper edge of the groove in the lever

(10).

•

If necessary, adjust the length of the

rod (5) with the fork (7), setting the pin (6)

and splint it.

•

Turning the adjusting screw (3), adjust

the lever (1) so that the parking brake be

fully engaged on the 3rd or 4th tooth of

the sector A under a force on the lever of

350 N.

•

Tighten the locknuts (2) and (6).

IMPORTANT!

With the brake pedals

interlocked, unsimultaneity of wheel

braking must not exceed 1 m as measured

by the wheel footprints.

Operation 28a. Brake pedal travel

(BELARUS-1221V.2)

Perform the operation described in the

section “Adjustments”.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands