Belarus 1221.2 Operator'S Manual Download

Page: 211 / 295

BELARUS-

1221.2/1221В.2/1221.3

Aggregation

210

and exclude the possibility of jamming!

•

The single-point coupling arrangement (hitch bar or tongue) of the machine shall

have a support and safety connecting chain or rope.

•

The coupling arrangement of trailed and semi-trailed machines shall be stiff to ex-

clude the collision of such machines with the tractor.

3.12.6 For the machines driven from the PTO

•

Only use the cardan shafts, which are recommended by the manufacturer of the

machine! Inspect regularly the technical condition of the cardan shaft.

•

The cardan shaft shall have an appropriate protective cover! The cover of the car-

dan shaft shall be secured against turning by means of a chain!

•

Prior to connecting or disconnecting the cardan shaft, disengage the power takeoff,

stop the engine and remove the ignition key!

•

Control at all times the correctness and safety of installation of the cardan shaft!

•

Prior to engaging the power takeoff, make sure that the selected rotational speed of

the tractor’s power takeoff does not contradict the allowable rotational speed of the aggre-

gate!

•

When using the synchronous power takeoff, make sure that the rotational speed

depends on the motion speed and the rotation direction changes of opposite when revers-

ing!

•

Prior to engaging the power takeoff, make sure that no people are present in the

dangerous zone of the aggregate!

•

Never engage the power takeoff when the engine is stopped!

•

When working with the power takeoff, make sure that there are no people in the

zone of rotation of the power takeoff and cardan shaft!

•

Disengage at all times the power takeoff when beginning driving on a step slope as

well as in cases where its operation is unnecessary!

•

After disengaging the power takeoff, the hazard due to the inertial mass remains for

some time. Do not approach the connected machine during this time! Performing any

works is only allowed after complete stop! Stop obligatorily the engine and remove the ig-

nition key!

•

Cleaning, lubricating or adjusting the aggregate driven from the PTO or cardan

shaft shall be only performed provided that the power takeoff is disengaged, the engine is

stopped and the ignition key is removed!

•

The disconnected cardan shaft shall be secured on the respective bracket!

•

After removing the cardan shaft, fit the protective cover to the end of the power

takeoff!

•

Inspect visually the cardan shaft, power takeoff and power intake shaft. Eliminate

immediately the faults revealed!

3.12.7 Rules concerning the instruments and the mechanisms of the machines and

tractor operating under the pressure

•

Caution! Do not forget about the presence of high pressure in the hydraulic and

pneumatic systems of the tractor and machines aggregated!

•

When connecting the hydraulic cylinders and hydraulic motor from the complete set

of the machine, check the correctness of connection of the hydraulic hoses!

•

Prior to beginning connecting the hydraulic hoses to the hydraulic system of the

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands