Belarus 1221.2 Operator'S Manual Download

Page: 50 / 295

BELARUS-1221.2/1221

.2/1221.3 Operating controls and instruments

Steering-Wheel-Mounted (

Multifunction)

switch (4)

It ensures the switching-on of the turn

indicators, toggling the beam

of the road

headlights (lower/upper beam),

upper

beam warning and horn beep

Turn indicator

Turning the lever (4) of the

steering-

wheel-mounted

switch forward or back-

wards switches on the right or left turning

indicator, respectively.

NOTE:

After completing the turn of the trac-

tor, the lever automatically returns to the

neutral position.

Horn beep

Pressing the switch lever end the beep

switches on.

Upper/lower beam

When the road headlights are switched on

pushing the lever switches on the “upper

beam” and pulling the same lever switches

on the “lower beam”.
Pulling the lever further from the “lower

beam” position up to the stop switches on

the upper beam (non-fixed position). Re-

leasing the lever puts it back in the “lower

beam” position.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands