Belarus 1221.2 Operator'S Manual Download

Page: 214 / 295

BELARUS-

1221.2/1221В.2/1221.3

Aggregation

213

- Determine the degree of loading the machine with the process materials ensuring

the safe operation of the tractor.

- Determine the necessity of twinning the wheels and filling the tyres with water solu-

tion.

- Assign the required pressure in the tyres depending on the maximum load and

speed under specific working conditions. The value of separate loads on the front and rear

axles of the tractor within the MTA shall not exceed the total allowed load-carrying capacity

of the front and rear tyres of the tractor, respectively, at the given speed and internal pres-

sure as specified in the Table of load-carrying capacity of the tyres.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands