Belarus 1221.2 Operator'S Manual Download

Page: 228 / 295

BELARUS-1221.2/1221

.2/1221.3 Possible defects and ways of their elimination

227

Defect, external manifestation

Way of elimination

erate

Check the integrity of the respective fuse

(25А, see the electric diagram) in the fuse

block located in the instrument dashboard.

Replace the blown fuse.

Check the presence of voltage at the air-

conditioner “M7” motor using a test lamp

when the switch is set to the ON position

and the presence of chassis on the engine.

If the electric circuits are in good order, but

no voltage is applied to the air-conditioner

“M7”, replace the switch.

When the air-conditioner is switched to the

cooling mode, warm air is supplied to the

cab

Destruction of the seal of the cock

ПО

-11 (or

ВС11).

Replace the cock ПО

11 (or ВС11)

Coolant leakage from the ventilation com-

partment of the cab

Rupture of the heater tubes (“unfreezing” of

the heater due to incomplete drainage dur-

ing the operation with water in the cold sea-

son of the year).

Replace the climatic unit of the air-

conditioner.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands