Belarus 1221.2 Operator'S Manual Download

Page: 17 / 295

BELARUS-

1221.2/1221В.2/1221.3

Technical data

Engine fuel system

Fuel pump

Type:

six-plunger, in-line with priming

pump: PP6M10P1f-3492 «MOTORPAL»

(Czechia) or 363.1111003-40.03 «YAZ-

DA» (Russia).

Regulator:

mechanical, variable speed,

with fuel supply corrector, automatic en-

gine fuel feed, smoke suppression

Injector

ФДМ

-22 with five-hole closed-

type atomizer.

Pressure at the beginning of fuel injection

— 21,6…22,4 MPa (220…228 kgf/cm

Fuel injection advance angle

till UDC

— 22

°±

Air cleaner

Type:

Dry with three-stage cleaning,

changeable paper filter element and

clogging indicator.

Filter elements:

paper filters – elements

made of highly porous paperboard.

Turbocharger:

ТКР

-7 type, radial inward

turbine and radial-flow compressor, as-

sembled on one shaft.
Installation of foreign producers turbo-

chargers is possible.

Engine cooling system

Type:

Pressurized liquid cooling system

with automatic temperature control by

friction clutch and two thermostats.

Oil cooling

: by oil-to-water heat ex-

changer, built into cylinder block.

Normal operating temperature

from 80°C to 97°C.

Cooling system capaci-

ty: 24 L

Engine lubrication system

Type:

Combined, with oil-to-water heat

exchanger built into cylinders block.

Oil filters:

centrifugal filter and filter with

changeable paper filter element.

Oil pressure at minimum speed

– 0.08

MPa (0.8 kgf/cm

at rated speed

–

0.28…0.45 MPa (2.8…4.5 kgf/cm

Lubrication system capacity

— 22 l.,

including engine crank case— 18 l.

Oil system capacity

— 22 l, including

engine crank case — 18 l.

Engine Starting System

24 V starting motor

Starting aid:

Heating plugs (for tractors “BELARUS-

1221.3”)

Clutch coupling

Type:

Dry friction, double-disk,

with tan-

gential suspension of pressure disk.

Disk diameter: 340 mm.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands