Belarus 1221.2 Operator'S Manual Download

Page: 49 / 295

BELARUS-1221.2/1221

.2/1221.3 Operating controls and instruments

Front windscreen washer switch (1)

Pressing the button (1) windscreen

washer the switches on.

Three-position light switch (2)

The button (2) has three positions:

1 — “OFF”;

2 — “Dashboard lighting, clearance

lights and number plate light ON”;

3 — “All control lamps units including

the front headlights ON”.

Fault signalling switch

(3)

Pressing the button (3) switches the

fault signalling on. There is a control

lamp inside the button, which blinks si-

multaneously with the flashing light sig-

nalling.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands