Belarus 1221.2 Operator'S Manual Download

Page: 166 / 295

BELARUS-

1221.2/1221В.2/1221.3

Adjustments

165

To choose a clearance

tighten a nut

(30),

check bearings axial play and turn a gear

(16) over a flange (22). If there is an axial

play the required tightness is to be pro-

vided by polishing of an adjustable washer

(23). If the bearings are adjusted in a

proper way

the torque of gear turning (16)

is to be within limits of

0,6...2,0

•

m which

corresponds to the force of 15...50 N on

the radius of the flange openings (22).

Splint the nut (30) without turning it off to

match the slits with apertures for a cotter

pin.

Tapered roller bearings (18) of the flange

(1)

(see Picture

-9) are to be adjusted

without a clearance by tightening of a nut

(17). After the

clearance is adjusted, the nut

is punched in two slits of the flange (1).

Fig.

-9

Tapered roller bearings

(6)

of the driving

gear (7) (see Picture

-9) are to be ad-

justed without tightness with an axial play

of not more than

0,05

mm. The adjust-

ment is to be done using split adjustable

gaskets (8) between a sleeve and a hous-

ing (5).

Tapered roller bearings

(11) of the pivots’

axles (9, 15) (see Picture

-9) are to be

adjusted with tightness of

0,01…0,06

using the adjustable gaskets (10) between

axles

(9, 15)

and a housing (5). Bearings’

clearance is not allowed. If the bearings

are adjusted properly the reducer shall

turn relative to the pivots’ axles with tor-

que of 16…20 N

•

Maximum rotation angle of the reducer

housing

(5) from the position which cor-

responds to an in-

line motion, is to be

within limits of 38...40

. Do adjustments

using a screw (20) (see Picture

-9).

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands