Belarus 1221.2 Operator'S Manual Download

Page: 69 / 295

BELARUS-1221.2/1221

.2/1221.3 Operating controls and instruments

Pneumatic system compressor co

trol

The handle of compressor control has

two positions:

•

“Compressor ON” – when turning

the handle so that the arrow on the

arm is directed backwards to tractor

motion;

•

“Compressor OFF” – when turning

the handle so that the arrow is di-

rected forward to tractor motion.

Выкл.

Disengage

Вкл.

Engage

Reversible Control Station BELA-

RUS -1221

.2)

Tractors are equipped with the reversi-

ble control station to broaden the pos-

sibilities of unitizing with the forward-

mounted agricultural machines.
The components of the reversible con-

trol station are as follows:

•

additional rear-located steering col-

umn with metering pump;

•

double foot controls of the engine

throttle, clutch and service brakes;

•

mechanism of seat reversal;

•

additional horn button and the en-

gine emergency modes indicators.

ATTENTION!

1. Tractor reverse control station in-

tends only for the field operations

at the reverse running.

2. When running at the reverse mode,

lock the standard service brake.

3. Never drive the tractor at the reverse

mode over the general-purpose

roads, during operations, not con-

nected with agriculture, and by lift-

on/lift-off of the tractor.

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands