Beijing Dahao Technology BECS-D56 Page 76 Owner'S Manual Download

Page: 76 / 188

Chapter 5 Management of Machine Parameters

"Success to read all parameters" will appear in screen.

After the above operations, the system parameters will resume to the status before

user updates the software. The embroidery machine can be used now.

5-8

Adjust Parameters of X

＆

Y Servo Drivers

These parameters are used for the Dahao all-servo high-speed machine, whose

main shaft uses Dahao servo motor and driver. Only the factory can rework these

parameters. Due to the password-protected function, you must input the factory

password for adjusting the parameters or performing the corresponding operation

to the machine. The operation process is as followed:

、

Press "

"in the main screen.

、

The system goes into

“

Machine Parameters Operation

”

interface. Move cursor to “Adj

Parameters of X

＆

Y Servo Drivers” and press “

”to enter “Parameters of X

＆

Y Servo

Drivers” window.

70 BECS- D56 computerized embroidery machine owner’s manual

Summary of Contents for BECS-D56





























































































































































































Search results

Summary of Contents for BECS-D56

Reviews:

Related manuals for BECS-D56

Brands by name

Popular brands

Beijing Dahao Technology BECS-D56, Owner'S Manual

Search results

Summary of Contents for BECS-D56

Reviews:

Related manuals for BECS-D56

Brands by name

Popular brands