Beijing Dahao Technology BECS-D56 Page 156 Owner'S Manual Download

Page: 156 / 188

Appendix

Ⅰ

Parameter Setting List

Number

Name

Recommended

Value

Range of Setting

Note

D13

Speed When
Over frame

0,1,2…30

D19

(AFC) Use

No, Yes

D20

(AFC) Interval
Time

0~15

C74

X direction
Frame Angle A

230

230~280

It is fit for high-speed
machine using Dahao
servo-motor driver.

C75

X direction
Frame Angle B

230

230~280

The same as above.

C76

Y direction
Frame Angle A

230

230~280

The same as above.

C85

Y direction
Frame Angle B

230

230~280

The same as above.

C72

Machine
Embroidery
Mode

Plain

Plain, hat, Clothes

C73

Frame Weight

0~20

C49

X Interval
Compensation

0.0mm

0.0

～

1.0

C50

Y Interval
Compensation

0.0mm

0.0

～

1.0

Main shaft Parameter

C07

Max. Speed

700-850

250

，

300

，

350

，…

,850

C09

Minimum
Speed

400

250,300,350…600

C08

Shift Stitch
Length

（

）

4.0(All-servo
high-speed
machine)

1.0~10.0(common

type

machine),3.0~6.0(All-servo
high-speed machine)

When the stitch length is
longer than the set value, the
machine will lower the
speed.

C10

Jump Stitch
Speed

750

400~750(common

type

machine),400~1100(All-servo
high-speed machine)

Set the rotation speed for
jump stitch.

C13

Set Run
Speed

80,90…150

C12

Startup
Stitches

2stitch

1 stitch ~9 stitch

Set the number of slow
stitch before acceleration.

D02

Startup Acce. 15

1,2,3…30

Increase the value to bring a

quicker speedup after pulling

the bar.

150 BECS- D56 computerized embroidery machine owner’s manual

Summary of Contents for BECS-D56





























































































































































































Search results

Summary of Contents for BECS-D56

Reviews:

Related manuals for BECS-D56

Brands by name

Popular brands

Beijing Dahao Technology BECS-D56, Owner'S Manual

Search results

Summary of Contents for BECS-D56

Reviews:

Related manuals for BECS-D56

Brands by name

Popular brands