Bedfont NOxBOX mobile Technical Manual Download Page 7

Page: 7 / 84

•

Ensure safe maintenance and repair-

Only qualified personnel should repair the

equipment. Protect personnel from hazards related to unexpected energizing, start-up, or

release of stored energy during servicing or maintenance by using strict equipment lockout/

tagout procedures.

•

Transportation-

When transporting the NOxBOX

trolley ensure the correct procedure is

adhered to. Always use the handle at the front of the trolley. Ensure cylinders are securely

fastened and inspect for trip hazards such as sample lines.

DANGER:

Failure to properly isolate equipment, electrical systems, and piping

can cause asphyxiation, fire, and/or explosion. Positively isolate the equipment

from the gas supply and the process material before performing repair work. It is

not sufficient to simply close valves. Lines and tubing must be blanked or

disconnected.

DANGER: Additional hazards may be associated with the gases used in your

application and with your equipment. Determine which hazards you may

encounter, and be prepared to handle them. Refer to the MSDS supplied with the

gases and all government egulations and industry safety standards, e.g. COSHH

in UK.

DANGER: Exposure to gases or vapours may cause asphyxiation.

Proceed with caution and in accordance with the MSDS.

Practically all gases can act as simple asphyxiates by displacing the natural oxygen in

the air. To prevent serious personnel injury and possible death, provide adequate

ventilation to the outside environment in areas where any process gas may

accumulate. Consider the increased potential for asphyxiation when pressure testing or

purging equipment with nitrogen or other non-air gases.

DANGER: Electric shock can kill. Use extreme caution if troubleshooting or

servicing this equipment. Do NOT bypass safety interlocks. An electrocution

hazard exists even after the equipment has been de-energized. Only qualified

personnel working in compliance with all customer requirements and applicable

federal/national, state/ provincial, and local codes shall perform the electrical

wiring.

Basic Hazards

2.1.1 Asphyxiation

2.1.2 Electrocution

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands