Bedfont NOxBOX mobile Technical Manual Download Page 22

Page: 22 / 84

4 INSTALLATION

WARNING: Installation of the BEDFONT® NOxBOX

system

involves potentially hazardous procedures. Only trained and

qualified personnel who have read and who understand the

instructions in this manual shall install this equipment. Wear

appropriate PPE, and, if applicable, turn off the power before

performing any installation, maintenance, repair, or troubleshooting

procedures.

The customer is responsible for obtaining information on any

applicable federal/national, state/provincial, and local codes or

insurance requirements that affect piping and electrical installation

and for obtaining all necessary approvals.

4.1 Unpacking Instructions

On first receiving this system, the NOxBOX

system should be carefully removed from its

packaging and visually inspected. Ensure all system components are present and free from visible

defect, wear or damage. Connect device to mains power immediately.

4.2 Assemble Delivery Unit to Trolley

WARNING: When attaching or detaching the head unit from the

trolley, the system brakes must be applied to stabilize the trolley

to prevent accident or injury.

The NOxBOX

delivery unit features a quick release system to enable quick and easy

assembly to the system trolley.

WARNING: Potential finger trap. Avoid injury; keep fingers clear

of the locking mechanism whilst placing the monitor onto the

trolley plate.

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands