Bedfont NOxBOX mobile Technical Manual Download Page 34

Page: 34 / 84

16.

If the system test failed, follow the diagnostic tips to correct:

Ensure that all connections on the Test Line Assembly are made as directed.

Ensure the NOxFlow sensor is orientated with the air flow in the direction of the

arrow marking, the dose portion closest to the sample end of the test line.

Ensure the valves are open on all NO supply cylinders.

Check the air flow is set to 10 L/min.

17.

If the system test fails a second time, the unit cannot be used for intelligent automated

delivery. Call the System Engineer, and replace the system.

18.

Once the system test has passed; shut off the O

flow, and disconnect the tested Line

Assembly from the supply line. The verified Line Assembly is ready to connect into the

patient ventilator circuit

If the NOxBOX

system is not to be used within next 10 minutes, turn

off the cylinder valves, detach the supply lines from Port 1 and Port

2, and release the line pressure using the purge needle at the back of

the monitor. Then re-attach the supply lines to Port 1 and Port 2.

WARNING: If the NOxBOX

system is left pressurized for more than 10

minutes while not in use, repeat the system test. Connect the Line

Assembly to the air supply as described in steps 11-17. Press Next.

The system test will run automatically.

Ventilator inspiratory limb showing NOxFlow placement before humidifier.

19. Connect the NOxBOX

to the patient ventilator inspiratory limb. See Section 5.3 onwards for

Patient Circuit connection diagrams.

The sample point adaptor should be connected immediately behind the patient Y-piece on

the inspiratory limb. To achieve consistent results, place a one-way flutter valve between the

sample connector and the Y-piece to prevent contamination of the sample from exhaled

breath.

20 . Connect the upstream end of the NOxFlow sensor to the upstream inspiratory limb tubing

The NOxFlow should be situated upstream of the humidifier.

Maintain the optimum 1m distance of ventilator tube between the sample point and the dose

introduction point on the NOxFlow for best performance (between 0.7 and 1.3m is ideal).

The system is now ready for dose entry and alarm setting procedures.

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands