Bedfont NOxBOX mobile Technical Manual Download Page 64

Page: 64 / 84

6.12 Manual Override

The NOxBOX

is equipped with a manual override delivery option to ensure continuous NO

delivery even in extreme conditions such as complete power loss or a catastrophic failure of the

intelligent delivery path. There are two controls associated with manual override delivery:

The Mode Selection Valve

The Manual Override

manual flow control valve

At commencement of NO delivery to the patient, it is advisable to check which flow setting on the

manual override system would best suit the current treatment session and set flow selector valve

to this value.

6.12.1 Determine Correct Flow Setting

Access the Manual Override Calculator

from the user settings screen.

Use the arrow keys to adjust the

ventilator minute flow to match the

patient ventilator settings.

The calculator table indicates the

approximate expected NO dose

delivery for each of the NO flow

settings (50-600ml) combined with

the vent/Oxygen flow.

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands