Bedfont NOxBOX mobile Technical Manual Download Page 53

Page: 53 / 84

6.7.3 Change Dose and Alarms

When changing the dose, the system recalculates the alarm values to

appropriate levels for the new dose setting. These values can be

confirmed or edited before returning to the Main Screen.

To change the dose from the main

screen, press the dose edit button.

The system will display the direct entry

dose keypad. Follow the system

instructions the same as when setting

the initial dose.

To change the gas alarm settings, press

the button corresponding to the alarm to

edit (image shows edit high NO alarm).

The edit dose screen shows the current

alarm value. Press the delete arrow to

clear this value and input a new value.

Press next to proceed, the system will

return to the main screen once the new

setting is accepted.

NOTE: the alarm settings have limits

beyond which it will not allow the alarm

to be set.

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands