Bedfont NOxBOX mobile Technical Manual Download Page 57

Page: 57 / 84

Restore the mains power to the

NOxBOX

If it is not possible to restore the

mains power, ensure the

Manual Override is prepared to

switch-on. See Section 6.12.

The system will automatically

shut-down when the battery charge

runs out.

No vent flow detected by the

NOxFlow for more than 30 seconds.

Ensure the NOxFlow is installed

correctly in the patient inspiratory

limb. The green printed arrow points

towards the patient.

This message may also appear

where insufficient ventilator flow is

present, such as with very low

tidal volume applications.

Increasing the bias flow may help

resolve this alarm.

The NOxBOX

has detected a critical

fault within the intelligent delivery

system, and can no longer

guarantee safe delivery function.

Engage the Manual Override (see

Section 6.12) and replace the

system as soon as practical.

Contact the Systems Engineer.

6.9.2 Gas Supply Alarms

An amber banner warning alarm

is triggered when one cylinder is

running low whilst there is a good

second supply cylinder detected.

To resolve this alarm, switch off the

empty gas cylinder at the valve.

Remove the gas supply line from

the rear of the monitor and

depressurise the line. The system

will automatically switch to the full

cylinder for continuous treatment.

Alternatively press the cross

button to mute the alarm for 2

minutes and discuss the banner

message.

Alarms

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands