Bedfont NOxBOX mobile Technical Manual Download Page 66

Page: 66 / 84

The system screen will display a

warning message that the system is

delivering through the Manual Override

mode.

Press the cross to dismiss this

message.

The “NO Dose” area of the main screen

shows a constant reminder that the

system is on Manual Override.

To revert to intelligent delivery, position

the mode selection valve to vertical.

6.12.4 Manual Override Flow Selector: Approximate NO flow values

50 cc/min

100

100 cc/min

200

200 cc/min

300

300 cc/min

400

400 cc/min

500

500 cc/min

Note all values shown are approximate to +/-

15%. Refer to look-up tables for indication of

dose per ventilator flow rate.

Monitoring of patient dose must be

implemented when using Manual

Override flow delivery of NO.

6.13 Shutdown

When ready to shutdown the system, press and

hold the power button on the monitor for two

seconds until the System Shutdown screen is

displayed.

Confirm shutdown on screen. Followon-screen

instructions.

600

600 cc/min

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands