Bedfont NOxBOX mobile Technical Manual Download Page 17

Page: 17 / 84

3.3.7 Accessory Label Symbols

Type B Applied Part: non-conductive
Single patient use device
Latex Free product
Device should not be used after the end of the year, month or day shown

3.3.8 Manual Override Flow Selector Valve Markings

50 cc/min

100

100 cc/min

200

200 cc/min

300

300 cc/min

400

400 cc/min

500

500 cc/min

Note all values shown are approximate

to +/- 15%. Refer to look-up tables for

indication of dose per ventilator flow rate.

Monitoring of patient dose must be

implemented when using Manual Override

flow delivery of NO.

3.4 System Components

Each NOxBOX

system has a unique serial unit

identification number of the format.

NI10001

This is found on the device label

(Figure 0-1) attached to the rear of the

device and should be quoted when contacting

the manufacturer or distributor for servicing and

repairs.

The rear label on NOxBOX

, additionally has the

manufacturer contact details and year of

manufacture for the device.

600

600 cc/min

Figure 0-1: NOxBOX

Device Label

2014

Summary of Contents for NOxBOX mobile





















































































Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands

Bedfont NOxBOX mobile, Technical Manual

Search results

Summary of Contents for NOxBOX mobile

Reviews:

Related manuals for NOxBOX mobile

Brands by name

Popular brands