manualshive.com logo in svg

baxter Flo-Gard 6301, Service Manual, Page: 58 / 252

Share
Download
baxter Flo-Gard 6301 Service Manual Download Page 58

7

Failure Identification Code Troubleshooting Table

7-12

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

4
5

Upstream occlusion was detected.

Check for spilled solution in 

sensor region. Ensure set is proper 

type and is properly loaded.

Remove upstream occlusion and 

reposition tubing. Clean the sensor 

with cotton swabs dampened with 

one of the agents listed in Table 

6-1. Remove fibers or foreign 

particles. Do not use hard 

instruments for cleaning.

Ensure ambient and solution 

temperatures are between 60° and 

100° F (15.5° and 37.7° C).

Raise or lower temperatures.

Perform the appropriate steps 

from “Automatic Test Mode 1: 

Calibration Mode 1” on page 9-14 

related to upstream occlusion.

Reading displayed in pump’s PRI 

RATE window must be within 

3242 and 3314. If not, recalibrate 

or replace the sensor.

Check for damage to door latch 

and hinges.

Replace any damaged parts.

6

Low battery voltage (10.4 V or 

less) was detected.

When BATTERY LOW alarm is 

on and CHARGING LED is off, 

check:
a. Tightness of AC plug
b. AC voltage source

 

 

c. Power fuse
d. Battery fuse

 

 

a. Plug in firmly.
b. When AC voltage is below 105 

VAC, connect pump to a correct 

voltage source.
c. Replace when it has failed.
d. Replace when it has failed.

Turn pump off and recharge for 

16 hours.

When alarm recurs after 

recharging, check and repair loose 

connections at battery terminals. If 

problem persists, replace battery.

7

Communication alarm was 

detected: A framing error, overrun 

error or parity error occurs during 

the communication with an 

external computer.

Check that the pump is in 

computer control mode. Check for 

the loss of the communications 

link. Verify that computer 

software is correctly loaded onto 

PC.

Place pump into computer control 

mode.
Ensure communication cable is 

plugged in and/or the cable is 

wired correctly.
Correct problems with PC 

software.

8

Communication time out alarm 

was detected: No communication 

between the pump and an external 

PC for a given period

See Failure Identification Code 7.

Place pump into computer control 

mode.
Ensure communication cable is 

plugged in and/or the cable is 

wired correctly.
Correct problems with PC 

software.

Table 7-3

Failure Identification Codes  — continued

Code

Cause

Checks

Corrective Action

Summary of Contents for Flo-Gard 6301





























































































































































































































































Reviews:

No comments