manualshive.com logo in svg

baxter Flo-Gard 6301, Service Manual, Page: 49 / 252

Share
Download
baxter Flo-Gard 6301 Service Manual Download Page 49

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

7-3

Troubleshooting

Determing the Software Version

Determing the Software Version

In order to troubleshoot the pump you must know the pump’s installed 
software version. Perform the following to detemine the pump’s software 
version:

1.

Turn the pump off.

2.

Press and hold the 

SILENCE

 key, then press the 

ON-OFF/CHARGE

 key.

3.

Record the software version displayed in the secondary VTBI display.

Alarms

The pump has a number of built-in safety features. Should a situation occur 
which requires operator attention or intervention, the pump stops infusing 
and sounds an audible alarm. The following are brief descriptions of these 
alarms.

AIR:

 An ultrasonic sensor in the pump head detects air in the administration 

set. Detection of an air bubble stops the infusion and illuminates the red 
ALARM LED. AIR is displayed in the Message Display and the audible 
alarm is activated.

OCCLUSION:

 The downstream occlusion sensor senses an increase in 

back-pressure between the patient and the pump, indicating an occlusion or 
closed clamp. When an occlusion is sensed, the pump stops, OCCLUSION 
is displayed in the Message Display, the red ALARM LED is illuminated 
and the audible alarm is activated.

UPSTREAM OCCLUSION:

 The upstream occlusion sensor senses a 

closed clamp or complete blockage upstream of the pump. When sensed, the 
pump stops, UPSTREAM OCCLUSION is displayed in the Message 
Display, the red ALARM LED is illuminated, and the audible alarm is 
activated.

BATTERY LOW:

 When approximately 15 minutes of running time remain 

during battery operation, BATTERY LOW is displayed in the Message 
Display, the yellow ALERT LED is illuminated, and the audible alert is 
activated. After approximately 15 minutes, the pump stops, BATTERY 
LOW is displayed on the Message Display, the red ALARM LED is 
illuminated, and the audible alarm is activated.

Table 7-1 the alarms and the possible causes of each. In all cases, fluid 
infusion is halted. Appropriate troubleshooting is discussed throughout the 
rest of this chapter.

Summary of Contents for Flo-Gard 6301





























































































































































































































































Reviews:

No comments