manualshive.com logo in svg

baxter Flo-Gard 6301, Service Manual, Page: 24 / 252

Share
Download
baxter Flo-Gard 6301 Service Manual Download Page 24

2

Controls and Indicators

2-4

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

16. 

PRI VTBI

 Key

Allows programming of the primary VTBI.

17. 

PRI START

 Key

Starts the primary infusion.

18. Plug Icon

Green LED, always lit while the pump is plugged in and the battery is charging.

19. MONITOR Legend

Lights for at least 2 seconds each time the host computer communicates with the 

pump when the pump is in monitor mode.

20. Battery Icon

Yellow LED, always lit while the pump is operating on battery power.

21. COMPUTER CONTROL 

Legend

Flashes when the pump is initiating communications with a host computer to enter 

the computer control mode. It is constantly illuminated when the pump is in 

computer control mode.

22. 

CLR

 Key

Clears any locked in values and programming values currently being entered.

23. 

SEC START

 Key

Starts the delivery of the secondary solution.

24. 

SEC VTBI

 Key

Allows programming of the secondary VTBI.

25. 

SEC RATE

 Key

Allows programming of the secondary infusion rate. 

26. Numerical Keypad

The numerical values for rate, VTBI, and time are entered with these keys.

27. OPTIONS Key/Legend

Enables the device to operate in special modes.

Item

Function

Summary of Contents for Flo-Gard 6301





























































































































































































































































Reviews:

No comments