Barco RLM G5i Performer R9010320 Owner'S Manual Download Page 19

Page: 19 / 150

3. Connections

3. CONNECTIONS

Overview

•

Power connection

•

Input Source Connections

•

5-Cable input

•

Composite Video Input

•

S-Video input

•

Digital Visual Interface (DVI) input

•

Computer input (RGB analog)

•

Serial Digital Interface

•

Communication connection

•

Extended configuration

3.1

Power connection

AC power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet.

Plug the female power connector into the male connector at the back of the projector. Fixate the power plug with the power cord
clamp.

The power input is auto-ranging from 90 to 240 VAC.

Image 3-1
Power connection

Power input

Power cord clamp

ON/OFF switch

Fuses

For continued protection against fire hazard :

•

refer replacement to qualified service personnel

•

ask to replace with the same type of fuse.

R5976815 RLM G5I PERFORMER 02/06/2006

Summary of Contents for RLM G5i Performer R9010320























































































































































Search results

Summary of Contents for RLM G5i Performer R9010320

Reviews:

Related manuals for RLM G5i Performer R9010320

Brands by name

Popular brands

Barco RLM G5i Performer R9010320, Owner'S Manual

Search results

Summary of Contents for RLM G5i Performer R9010320

Reviews:

Related manuals for RLM G5i Performer R9010320

Brands by name

Popular brands