Barco RLM G5i Performer R9010320 Owner'S Manual Download Page 84

Page: 84 / 150

8. Image Menu

Input balance is also available for a component video source under following conditions:

•

A component video signal is present on the BNC’s.

•

”Data on BNC’s” is selected in the

Source selection menu.

•

Pr/Y/Pb is selected in the Advanced menu of the corresponding image file.

The procedure is the same as for a data source except:

•

The white balance happens only on Green.
Adjust until bright spots appear in the image.

Image 8-43

•

The black balance happens on the three colors.
The PR and PB connector have to be removed from the input.
Adjust until noise appears in the image.

Image 8-44

8.10 AGC on Video

AGC

Automatic Gain Control: allows an automatic amplitude (gain) control of the incoming video signal

AGC is only for Video signals.

Enabling/disabling the AGC

1. Press

MENU

to activate the menu bar.

2. Press

→

to select the

Image

item.

3. Press

↓

to pull down the

Image

menu.

4. Use

↑

↓

to select

AGC on Video.

R5976815 RLM G5I PERFORMER 02/06/2006

Summary of Contents for RLM G5i Performer R9010320























































































































































Search results

Summary of Contents for RLM G5i Performer R9010320

Reviews:

Related manuals for RLM G5i Performer R9010320

Brands by name

Popular brands

Barco RLM G5i Performer R9010320, Owner'S Manual

Search results

Summary of Contents for RLM G5i Performer R9010320

Reviews:

Related manuals for RLM G5i Performer R9010320

Brands by name

Popular brands