Barco HDF W series, Service Manual

Page: 331 / 337

Index
LPS failure fan 1 38
LPS failure fan 1 & 2 35
LPS failure fan 2 39
LPS failure pfc driver 39
LPS failure power stage driver 39
LPS internal error 38
LPS internal voltage error 38
LPS invalid parameters 35
LPS mains voltage too high 38
LPS mains voltage too low 37
LPS no lamp ignition detected
35
LPS output current too high 36
LPS output current too low 36
LPS output power too high
35
LPS output power too low 35
Lps read failed 93
Lps reply no ack 94
LPS requested output power too high with low mains voltage
38
LPS start-up fail LPS power stage 35
LPS start-up fail PFC power stage 35
LPS Temperature ambient too high 36–37
LPS temperature heatsink output diode too high 37
LPS temperature primary heatsink 1 too high 36
LPS temperature primary heatsink 2 too high 36
LPS temperature transformer too high 37
Lps write failed
93
Lseek failed 92
Lsm read failed
94
Lsm reply no ack 94
Lsm write failed 93
Mains voltage high 74–75
Mains voltage low 74
Mcb read failed
93
Mcb reply no ack 94
Mcb write failed 93
Mmap failed 93
Motor board calibration 84
No dmx shutdown 89
No memory 91
no signal shutdown 89
Non blocked signal 91
Opening shutter failed 84
Overtemp 72
Overtemperature dimming 88
Port timeout 91
Power interrupt 71
Power supply primary DCDC temp high 69
Power supply primary DCDC temp low 68–69
Power supply primary DCDC temp open 69
Power supply primary PFC temp high
70
Power supply primary PFC temp low 69–70
Power supply primary PFC temp open 70–71
Power supply secondary temp high 67–68
Power supply secondary temp low 67
Power supply secondary temp open 68
Power supply secondary temp short 68
Projector type invalid 90
Pump voltage high
75
Pump voltage low 75
Read failed
92
Read lamp status failed 35
Reading lamp info module 87
Recieve Over
fl ow 92
Recieve Parity 92
Red DMD temp high 54–55
Red DMD temp low 53–54
Red DMD temp open 55
Red DMD temp short 56
Red form. start failed
33
Rod in temp high 66
Rod in temp low 65–66
Rod in temp open
67
Rod in temp short 67
Rs485 selection 91
Setting FCB mode 53
Setting XLR control 53
Shutter current too high 86
Shutter time out 85
Spi Ioctl failed 92
Storage: restoring without any preceding storing 96
Storage: successful restoring 96
Storage: successful restoring with fall back mgt
fi le 96
Storage: unsuccessful restoring 96
Tilt orientation invalid 89
Tilt rotation not allowed 87–88
Transmit over
fl ow 92
Usb restoring settings failed 90
Usb saving settings failed 90
Vertical lens shift driver 85
Vertical lens shift end of range 84–85
Vertical lens shift stopped 87
Watchdog 72
Write failed 92
Xlr overload 76
Error code number 33–96
100000 91
100001 91
100002 91
100003 91
100004 91
100005 91
100006 91
100007 91
100008 91
100009 91
100010 91
100011 92
100012 92
100013 92
100014 92
100015 92
100016 92
100017 92
100018 92
100019 92
100020 92
100021 92
100022 93
100023 93
100024 93
100025 93
100026 93
100027 93
100028 93
100029 93
100030 93
100031 93
100032 93
100033 94
100034 94
100035 94
100036 94
100037 94
100038 94
100039 94
100040 94
100041 94
100042 94
100043 94
100044 95
100045 95
100046 95
100047 95
100048 95
100049 95
100050 95
100051 95
100052 95
100053 95
100054 95
100055 96
100056 96
R5905312 HDF W SERIES 24/01/2013 327