1.
Only with INTERF.PARAM. > NETWORK PARAM. > WEB Server = „enabled“
2.
Only with BLDC firmware version V4-T36 or higher
3.
Only with INTERF.PARAM. > NETWORK PARAM. > Time client = „Enabled“
4.
Only with at least one data block stored in the flash memory
5.
Only with rewinder
6.
Only with cutter
7.
Only with „AP 5.4 peripheral“
8.
Only if SYSTEM PARAMETERS > Periph. device = „Tear-off edge“ or
„Tear off + sensor“
10.
Only with activated MONARCH LANGUAGE INTERPRETER™
12.
Only if PRINT PARAMETERS > Punch mode = „Manual“
13.
Only in production mode
14.
As in 13. or with a setting value
> 0
18.
Only with installed RFID option
20.
Only if SYSTEM PARAMETERS > Periph. device = „Dispenser“
21.
Only if SYSTEM PARAMETERS > Periph. device = „Int Rewinder“
22.
Only with an activated RFID
option
23.
Only with I/O board
24.
Not with I/O board
29.
Availability depends on device configuration
30.
Only with a memory card inserted
03/10 Rev. 5.05-00
USER- / SERVICE MANUAL
Info-Printouts & Parameters
AP 5.4 Gen II – AP 5.6
10
AP 5.4
Pa
ra
m
et
er
s
AP 5.4 Parameter
PRINT INFO
PRINT PARAMETERS
INTERFACE PARA
(INTERFACE PARA cont.)
(INTERFACE PARA cont.)
SYSTEM PARAMETER
Printer status
Print speed
> EASYPLUGINTERPR
Parity
> OPTIONS
Foil end warning
Memory status
Feed speed
Interface
Stop bits
RFID Option
Foil warn stop
Font status
Material type
Spooler mode
Data synch.
StandAlone Input
Print Interpret.
Flashdata status
4
Material length
Printer ID No.
Frame error
Character sets
Service status
Material width
Spooler size
> DRIVEASSIGNMENT
Character filter
Dottest endless
Print direction
Offline mode
> USB
Drive C
Light sens. type
Dottest punched
Punch offset
Interface delay
USB select
Drive D
Head-sensor dist
13/14
Reference label
Bar code Multi.
Sens. punch-LS
RFID status
22
Tradit. Imaging
13
> COM1 PORT
> NETWORK PARAM.
Foil mode
UPC plain-copy
Baud rate
IP Addressassign
Turn-on mode
EAN Readline
No. of data bits
IP Address
Error reprint
EAN sep. lines
Parity
Net mask
EasyPlug errors
Cut mode
6
Stop bits
Gateway address
Single job mode
Cut position
6
Data synch.
Port address
Head resistance
Double cut
6
Frame error
Ethernet speed
Temp. reduction
Rewind direction
5
MAC address
Thin line emphas
13
Rotated barcodes
> COM3 PORT
23
SNMP agent
Voltage offset
Dispenseposition
8
Baud rate
23
SNMP password
13
Miss. label tol.
X – Printadjust
No. of data bits
23
FTP server
Gap detect mode
Y – Printadjust
Parity
23
FTP password
13
Periph. device
Punch mode
Stop bits
23
WEB server
Singlestartquant
Punch level
12
Data synch.
23
WEB display refr
1
External signal
Serial Port Mode
23
WEB admin passw.
13
Start print mode
24
Frame error
23
WEB supervisor p.
13
Print contrast
Time client
Ram disk size
> COM4 PORT
Time server IP
3
Font downl. area
Baud rate
Sync. intervall
3
Free store size
No. of data bits
DHCP host name
Print info mode
F
W
7.34 Pre 4081
