manualshive.com logo in svg

Avaya 4524GT, Configuration Manual

Share
Download
Avaya 4524GT Configuration Manual Download Page 330

Variable

Value

TimeMark

Indicates the TimeFilter for this entry.

LocalPortNum

Identifies the local port on which the remote
system information is received.

Index

Indicates the arbitrary local integer value
used by this agent to identify a particular
MSAP. An agent is encouraged to assign
monotonically increasing index values to
new entries, starting with one, after each
reboot.

PSEPowerAvailable

Specifies the power available (in units of 0.1
watts) from the PSE connected remotely to
this port.

PSEPowerSource

Defines the type of PSE Power Source
advertised by the remote device.

• primary: indicates that the device

advertises its power source as primary.

• backup: indicates that the device

advertises its power source as backup.

PSEPowerPriority

Specifies the priority advertised by the PSE
connected remotely to the port:

• critical: indicates that the device advertises

its power priority as critical, see RFC
3621.

• high: indicates that the device advertises

its power priority as high, see RFC 3621.

• low: indicates that the device advertises its

power priority as low, see RFC 3621.

Viewing neighbor PoE PD information using EDM

Use this procedure to display LLDP PoE PD information for the remote system.

Procedure steps

1. From the navigation tree, double-click 

Edit

.

2. In the Edit tree, double-click 

Diagnostics

.

3. In the Diagnostic tree, double-click 

802.1AB

.

System configuration using Enterprise Device Manager

330     Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands