manualshive.com logo in svg

Avaya 4524GT, Configuration Manual

Share
Download
Avaya 4524GT Configuration Manual Download Page 228

Variable definitions

Use the information in the following table to help you understand the base unit information
display.

Variable

Value

Type

Indicates the switch type.

Descr

Describes the switch hardware, including number of ports
and transmission speed.

Ver

Indicates the switch hardware version number.

SerNum

Indicates the switch serial number.

LstChng

Indicates the value of sysUpTime at the time the interface
entered its current operational state. If you entered the
current state prior to the last reinitialization of the local
network management subsystem, the value is zero.

AdminState

Specifies the administrative state of the base unit switch.
Values include enable or reset.

 Important:

In a stack configuration, the 

reset

 command resets

only the base unit.

OperState

Indicates the operational state of the switch.

Location

Specifies the physical location of the switch.

RelPos

Indicates the relative position of the switch.

BaseNumPorts

Indicates the number of base ports of the switch.

TotalNumPorts

Indicates the number of ports of the switch.

IpAddress

Indicates the base unit IP address.

RunningSoftwareVer

Indicates the version of the running software.

Renumbering stack switch units using EDM

Use this procedure to change the unit numbers of switches in a stack.

System configuration using Enterprise Device Manager

228     Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands